Installation of Curt Tow Bar # C19745

Question

Question:

I purchased Curt 19745 tow bar, can you send me installation instructions for a 97 Jeep TJ. Thank you.

asked by: Luiz P

0

Expert Reply:

I've linked the install details for the Cur tow bar, part # C19745, to this page. They're also linked on the product page.

expert reply by: Charles S

0

Answer 1

I have a solution for you, however, I would not recommend mounting a tow bar directly to a bumper on a Jeep, whether it is OEM or an aftermarket bumper. Jeep does not recommend towing the Wrangler with the OEM bumper because it was not designed to…

view full answer...

Answer 2

The Curt Tow Bar with Adjustable-Width Arms #C19745 is a universal tow bar system and the instructions basically say to make sure to attach the clevis mounts to the frame of the vehicle. You can mount it to the bumper or you can remove the bumper…

view full answer...

Answer 3

For your 2012 Jeep Wrangler Unlimited we have two options for base plate kits to attach to the D-rings of your bumper. We have the part #RM-035 which is the correct fit if you have 3/4 inch D-rings or the part #RM-035-1 which fits if you have 1…

view full answer...

Answer 4

There is no specific speed rating associated with the Curt Tow Bar with Adjustable-Width Arms #C19745. When using this or any other tow bar you are going to want to not only follow your local laws but look in your tow vehicle's…

view full answer...

Answer 5

I have a solution for you, and there are some brake controllers available that can be used with a plug and play wiring harness to ease installation; however the Hayes Energize III #HA81742B is not one of those controllers and it would need to be…

view full answer...

Answer 6

For brake controllers like your Hayes Lemmerz Energize III part #HA81742B the white wire gets grounded, the black wire runs to a constant 12 volt power source, the red to a wire that only has voltage when brakes are applied (normally on the brake…

view full answer...

Answer 7

The Curt Tow Bar with Adjustable-Width Arms - Car Mount #C19745 is a universal-style fit so you would only need a flat, nearly vertical area on your 2004 Jeep Wrangler's bumper, or one can be fabricated. I've added a portion of this…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Installation of Curt Tow Bar # C19745

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching