Plug Needed for Thule Rapid Gutter Feet

Question

Question:

I bought thule gutter foot mounts but they are missing a key/plug. Would that prevent me from fully tightening them down? If thats what I need could you advise me a on a part number? Thanks

asked by: Craig F

0

Expert Reply:

Not having the plug on your Thule Rapid Gutter Feet, like part # TH300R, should not prevent you from being able to fully tighten the feet.

Since the locking knob on your Gutter Feet use the same core as other Thule products you can use part # 8524023006 to plug those holes. If you would rather use actual locks on the feet then you would want to go with the 4-pack # TH450400.

expert reply by: Jon G

0

click to enlarge

Answer 1

We do have replacement end caps for your Thule AeroBlade Edge Roof Rack TH7602-TH7602! The Replacement Endcap - Left is #TH1500052333 while the Replacement Endcap - Right is #TH1500052334. If you take a look at the accompanying photos you will be…

view full answer...

Answer 2

I do have a possible solution for you but the most well equipped 2018 Jeep Wrangler JL Unlimited has a maximum tongue weight capacity of 350 lbs therefore, the Draw-Tite Max-Frame Trailer Hitch Receiver part #DT78MR will not increase your tongue…

view full answer...

Answer 3

You would need the lock plug part #8524023006 to go along with the Replacement Endcap #TH1500052333 that you referenced as it is not included.

view full answer...

Answer 4

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable. If your capsule is sealed, then your best option is to replace the lights with new lights like part #403026 and #403076.…

view full answer...

Answer 5

We normally recommend moving roof rack accessories to the rear of the vehicle as much as possible as that allows for best vision and the least amount of wind noise. Every application is different though so as long as you have the rack secured well…

view full answer...

Answer 6

It looks like some of the customer submitted photos for the Malone roof rack part #MPG215 show the rack installed backwards. The thicker portion needs to face forward. I attached a picture that shows the correct orientation of the bars for you to…

view full answer...

Answer 7

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Plug Needed for Thule Rapid Gutter Feet

Products Referenced in This Question

Continue Researching