Towing System Compatible with 2017 Ford Edge Titanium
Question:
I have a 2017 Ford Edge Titanium. Will a 2-inch ball fit this reciever hitch?
asked by: David H
Expert Reply:
The Curt Trailer Hitch Receiver - Class II # C12140 is a confirmed fit for your 2017 Ford Edge Titanium. Then you can use ball mount # C45521 you asked about along with 2 inch hitch ball # A-82 and pin/clip # F-4.
For your trailer wiring, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118677. This custom-fit T-One connector plugs into your Ford Edge's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse. Once installation is complete, the 4-way connector will be stowed beneath your Ford Edge, near the trailer hitch. Use mounting bracket # 18144 and # 18140 for a clean look.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
No-Drill Mount for Electrical Mounting Bracket - Short
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 4 Round
- 5 Round
- Tow Ready
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Measure for Trailer Hitch Drop
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Q&A: Ball Mount Recommendation for 2012 Kia Forte Curt Trailer Hitch and 2 Hitch Ball
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended 1-1/4 Class 1 Hitch for a 2023 Honda HR-V
- Q&A: How to Determine Correct Curt 4-Way Wiring Harness For 2024 Kia Telluride
- Article: Trailer Hitch Receiver Sizes
- Q&A: Recommended Hitch for a 2024 Honda HR-V
- Q&A: Recommended Trailer Hitch for a 2024 Honda HR-V
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Curt Trailer Hitch, Euro Ball Mount, and Wiring Harness for a 2006 Ford Freestyle