Diameter of Post on Ramp Door Hinge # PLR1902

Question

Question:

Hello, Can you please tell me the size of the post this hinge rotates around. I need to Cut this to make it fit my existing trailer. Thanks PLR 1902

asked by: Glenn

0

Expert Reply:

The diameter of the post on the Ramp Door Hinge # PLR1902 that you referenced is 1 inch. I attached a picture that has several other dimensions for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, the hinge part #PLR1902 will work well for you. If you used 6 of these on a fold-out style stage it would have the capacity needed and would operate well for you.

view full answer...

Answer 2

The Ramp Door Hinge #PLR1902 that you referenced does not come with 2 of the plates for welding. You will weld the plate to one surface and the outside ends of the pin to the other for installation. For a hinge that has 2 of the plates you would want…

view full answer...

Answer 3

The Polar Ramp Door Hinge - Steel #PLR1902 is not removable as removing that pin would compromise the zerk grease fitting and seals related to it. I confirmed this with my tech contact at Polar.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Ted, so if you look in the bed of your truck and see 5 holes/pucks that would mean you have the OEM prep. I'd assume if you had it you'd have seen them by now. If you had it you'd only need a ball like the part #C60618. If you…

view full answer...

Answer 9

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

Installing ta Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Adapter Pin Box like the #325-GH-8045 would not void the warranty of your camper, and Gen-Y makes some of the most durable parts on the market. I really like this as an alternative to…

view full answer...

Diameter of Post on Ramp Door Hinge # PLR1902

Product Page this Question was Asked From

Continue Researching