Comparing the Curt Front Hitch Part # C31023 and Draw-Tite Front Hitch for a 2012 GMC Sierra 2500

Question

Question:

2012 GMC 2500 HD front hitch receiver. you show 2 different hitches, I am looking at the lowest one. 8inch lift with 37inch so I dont want to cut anymore of the front valance than I have to. I also have a black horse bull bar on the front so I may put a little extension to get past it. not looking at loading alot of weight, just need some extra room to carry things when I pull my camper, golf cart in the bed and camper hitch is usually loaded. Thanks

asked by: Ray

1

Helpful Expert Reply:

The Curt Front Mount Trailer Hitch Receiver part # C31023 which is a fit for a 2012 GMC Sierra 2500 will hang down further than the other option we have for you which is the Draw-Tite Front Mount Trailer Hitch Receiver part # 65078 excluding Denali. This means that there will be much less trimming required to clear the lower bumper valance in order to make it work.

Please note that the above hitch is only tested on stock vehicle's without a lift or bull bar. You will need to take a look at the install instructions which I have attached for you to make sure it will not interfere with the components you already have installed.

expert reply by: Conner L

1

Answer 1

It's not uncommon for people to use bike racks in front hitches like you are asking about. You wouldn't want to put a bike rack cover on the setup though as it would whip around pretty violently no matter how tight you thought you could get…

view full answer...

Answer 2

You can definitely carry the Thule EasyFold XT #TH903202 with a front mount hitch on your GMC Sierra 2500 Denali! It looks like you input a 2019 GMC Sierra 2500 in as your vehicle. If this is the year that you have then we have 2 different front…

view full answer...

Answer 3

I recommend the Draw-Tite front hitch #65078 for your 2012 Chevy 2500HD because it's position provides ground clearance and will work well with a winch mount. Attached is what it looks like installed. It has a line pull rating of 9,000 lbs. As…

view full answer...

Answer 4

In addition to the Curt Front Mount Trailer Hitch Receiver #C31023 for your 2012 GMC Sierra, you are correct that you will also need at least a single roof rack bar like the Darby Turbo rack #DTA968 and a carrier like the LongArm #Y01149-1150 that…

view full answer...

Answer 5

For a front hitch for your 2012 Chevy Silverado 3500 the Curt hitch part #C31023 is a confirmed fit and would work great for mounting a bike rack like the Swagman XC2 part #S64650 that you referenced. In this price range for a bike rack I like to…

view full answer...

Answer 6

To use SnowBear snowplow #SB324-167 you will need to use custom brackets #SB397-111 on your 2012 Chevy Silverado 2500. What I recommend is to use a front mount hitch model, #SB324-172, with front hitch #C31023. This way the overall cost will be lower…

view full answer...

Answer 7

The front ends of the Silverados and Sierras like your 2018 GMC 2500 are a bit different but the fascia trimming required is the same as you can see in the two attached pictures when installing front hitch #65078. Basically a hole gets cut through…

view full answer...

Answer 8

You will not need to remove the front bumper when installing the Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2" #65078. This will, however, require trimming of the front fascia to allow access for the hitch receiver opening.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...