Can Superchips Flashcal F5 Calibrator be Used on Two Different 2018 Jeep Wrangler Rubicons?

Question

Question:

My wife and I both have a 2018 Jeep Rubicon JK. Can I use the same Superchips F5 Flashcal for both Jeeps?

asked by: Scott B

0

Expert Reply:

No, you cannot use the same Superchips Flashcal F5 Calibrator for Jeep Wrangler # SU3571 on both your 2018 Jeep Wrangler Rubicon and your wife's Wrangler. The Flashcal can only be used with a single vehicle at a time because the original tune is stored in the unit's memory.

expert reply by: Kyle S

0

Answer 1

Yes, the Superchips Flashcal F5 Calibrator #SU3571 that you referenced has been confirmed to fit your 2016 Jeep Rubicon Wrangler and would help you change the speedometer for different tire sizes, but it will not give you additional horsepower.…

view full answer...

Answer 2

Yes, if you set the vehicle you had the Superchips Flashcal F5 Calibrator #SU3571 installed on back to stock you will be able to then use the calibrator on a second vehicle.

view full answer...

Answer 3

You will want to visit superchips website to verify you are able to update your Superchips Flashcal F5 Calibrator #SU3571. As long as it is able to have the latest software you should be able to use this on a different compatible vehicle.

view full answer...

Answer 4

As long as you set the Superchips Flashcal F5 Calibrator #SU3571 back to the factory settings for the initial vehicle then yes, you can definitely use it on a new vehicle. If you forget to set the initial vehicle back to factory settings you can…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 9

All the brake controller needs to sense a trailer connection so that you can test it is a slight amperage draw on the output circuit. For that you can use a circuit tester like the part #PTW2993 with one pin grounded and the other on the output pin.…

view full answer...

Answer 10

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 11

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Can Superchips Flashcal F5 Calibrator be Used on Two Different 2018 Jeep Wrangler Rubicons?

Product Page this Question was Asked From

Continue Researching