Installation of Kodiak Stainless Steel Mounting Bracket # KCMB10RS

Question

Question:

Does the stainless steel mounting bracket for Kodiak disc brakes come with the bolts and nuts to mount the bracket to the axle? If not, do you carry the stainless 7/16X 20 nuts and bolts to mount the bracket?

asked by: Victor V

0

Expert Reply:

The Replacement Mounting Bracket for Kodiak Disc Brake Caliper - Over-the-Hub - Stainless - 3,500 lbs # KCMB10RS do not come with the mounting hardware. We have the Mounting Bolts and Hardware for 10" Single Brake Assembly # BRKH10AS which are steel bolts compatible with the bracket but they are steel and not stainless steel.

expert reply by: Jason S

0

Answer 1

I contacted the manufacturer to confirm that the Replacement Mounting Bracket for Kodiak Disc Brake Caliper #KCMB10RS will work with your Kodiak Disc Brake Caliper #KDBC225S (225 SS). They were able to confirm that those two parts will work…

view full answer...

Answer 2

I attached a picture that has all of the mounting hole dimensions of the Kodiak Disc Brake Bracket #KCMB10RD.

view full answer...

Answer 3

The brake pads that come with the #K2R35S are the #K225CP which are made of carbon ceramic and have a lifetime warranty. If you did want stainless calipers as well you'd want the part #K225CPSS to.

view full answer...

Answer 4

The Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Stainless Steel - 3,500 lbs #K2R35S you were looking includes brake pads with the standard steel backing plate. If you would rather have brake pads with a stainless steel backing plate then…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Installation of Kodiak Stainless Steel Mounting Bracket # KCMB10RS

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching