Where to Install the Timbren Spacer on a 2016 Ram 1500

Question

Question:

I am attempting to use these on my Ram, however the spacers are big enough around that they are stopping the unit from going up into the bell enough to lock in place. I noticed that when using them without the spacer, the upper part of the “spring” part of the unit seats up inside the bell.

asked by: Scott

0

Expert Reply:

If you take a look at the attached photo, the 1" spacer part # A25723-90AH00 for 3/8" diameter hole or part # TA25723-90AD00 for 1/2" diameter hole will need to be placed in between "2" and "3" when using the Timbren Rear Suspension Enhancement System part # TDR1500DQ on a 2016 Ram 1500.

Please note that you will need a longer bolt to install the Timbren springs once the spacer is added. You can aquire this bolt at your local hardware store.

expert reply by: Conner L

0

click to enlarge

Answer 1

The Timbren Rear Suspension Enhancement System part #TDR1500DQ is a good option for a 2020 Ram 1500. That said, it won't get rid of all squat since the suspension has to reach a threshold before they even engage. If you like, you can get rid of…

view full answer...

Answer 2

In order to install the Timbren Rear Suspension Enhancement System part #TDRTT1500 on a 2019 Ram 1500 which is an excellent choice you will need to match the number of spacers to the amount of lift with the Timbren 1" Spacer For Raised Frame…

view full answer...

Answer 3

The difference between the two is how much weight they can support. The Air Lift 1000 #AL60818 can support 1000 lbs, while the #AL60818HD can support 2100 lbs. Going with the higher rated option, #AL60818HD is recommended. Because the system is very…

view full answer...

Answer 4

The Air Lift AirLift 1000 Air Helper Springs for Coil Springs will work in the exact manner you want; improving the ride and how your 2014 Ram 1500 handles when you are towing. These air springs will reduce the strain on your Ram's suspension and…

view full answer...

Answer 5

For a lift spacer that fits a Timbren kit for your 2020 GMC Sierra like the #TGMRCK25D you'd need a spacer with a 3/8 inch diameter hole like the #A25723-90AH00.

view full answer...

Answer 6

It is permissible to stack two 1-inch spacers #A25723-90AH00 to give you a total of 2-inches of height adjustment for your Timbren rear axle kit. Rear axle jounce spring kits like those from Timbren are intended primarily for use with supporting…

view full answer...

Answer 7

For a heavy duty Timbren confirmed as a fit for your 2015 Chevy Silverado 2500HD we have the part #TGMRTT35D as a confirmed fit. This would be your best option. Now it sounds like your lift is a body lift which does not change the suspension in any…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Where to Install the Timbren Spacer on a 2016 Ram 1500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching