Replacement Hitch Lock for a Yakima ROC 2 Bike Rack Part 8002573

Question

Question:

Here are the photos

asked by: Nathaniel

0

Expert Reply:

Can you please send the picture of the bike rack you have in response to this email?

expert reply by: Conner L

0

click to enlarge

Nathaniel

6/8/2018

Here are the photos

Reply

Conner L.

6/8/2018

Thanks for the photo! You are correct in that you have the Yakima ROC 2 Bike Rack part 8002573. The correct replacement hitch lock for your bike rack is the Yakima HitchLock part # Y07235. This lock comes with a new lock and two keys. If you would like to use your A134 keys you have now then you will need the Replacement Body for Yakima HitchLock part # 8820048 and the A134 lock core part # Y8771-A134.

Reply

Answer 1

The Yakima Hitchlock part #Y07235 actually attaches to the end of the hitch pin of your Yakima bike rack. You still have to use the threaded hitch pin with this to get the lock to function.

view full answer...

Answer 2

Yes, the Yakima HitchLock part #Y07235 if a fit for all Yakima bike racks so it would fit and work well on yours. I attached a review video for this product for you to check out as well.

view full answer...

Answer 3

When it comes to your Yakima bike rack I recommend going with The Yakima HitchLock for Yakima Hitch Mounted Bike Racks - Same Key System #Y07235. This lock works with any Yakima hitch mounted bike carrier. It attaches to the end of the existing…

view full answer...

Answer 4

The clamps on the Yakima OnRamp Bike Rack for 2 Electric Bikes #Y36FR can spin around that mast as well as rotate to accommodate different frame designs. You should have absolutely no issues fitting 2 step-thru frame bikes on this rack since the…

view full answer...

Answer 5

The Yakima HitchLock for Yakima Hitch Mounted Bike Racks #Y07235 attaches to your anti-rattle bolt and keeps your bike rack locked to your hitch. An even more secure setup is the Yakima LockUp Hitch Lock and Cable Lock #Y07238. This kit not only…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The Tow Defender #RM-4700 you found is really our best option to protect the front of your 2024 Chevrolet Trax. This screen helps to deflect any road debris back down to the ground to keep it traveling under your Trax. This particular cover is…

view full answer...

Answer 10

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport Rider SE…

view full answer...

Replacement Hitch Lock for a Yakima ROC 2 Bike Rack Part 8002573

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching