Ladder Rack Compatibility with 2003 Toyota Tundra and BAKFlip Tonneau

Question

Question:

I have a backflip tonneau cover need a ladderrack thats fits into the stak pockets holes. Versus a rack rack that goes over.the edge of my bedrail. Can you help me out. Thanks

asked by: Michael

0

Expert Reply:

The Thule TracRac SR Sliding Truck Bed Ladder Rack # TH43001XT-501 is not a confirmed fit for your truck. These TracRac sliding racks are compatible with the BAKFlip Tonneau covers because they utilize the stake pocket locations and the tonneau utilizes rails inside the side rails. Ufortunately they don't have any confirmed fit for your 2003 Toyota Tundra. It is very possible it will fit, but I can't confirm as Thule has not tested the fit on your truck.

I've linked the page to all of the confirmed fit options for your truck, but unfortunately none of them utilize the stake pockets for mounting so they aren't directly compatible with your tonneau.

expert reply by: Jason S

0

Michael

6/12/2018

I have a backflip tonneau cover need a ladderrack thats fits into the stak pockets holes. Versus a rack rack that goes over.the edge of my bedrail. Can you help me out. Thanks

Reply

Jason S.

6/12/2018

The options for what you are seeking are very limited as they aren't confirmed to fit meaning they have either not been tested or do not work to their specified capacities. Other than the TracRac SR, the only other ladder rack that I know works with the BAK BAKFlip Tonneau is the Adarac Pro Series Custom Truck Bed Ladder Rack - Aluminum - 500 lbs # A4000960 because it fits in the stake pockets and does not slant in to impact the folding of the tonneau. This is not a confirmed fit on your vehicle but may be the best option. If you have a short bed, you would instead use # A4000948.

Reply

Answer 1

I did some online research and I found out the Peragon tonneau covers leave the stake pockets uncovered. You need the stake pockets to install the Thule TracRac SR Sliding Truck Bed Ladder Rack w/ Cantilever - 1,250 lbs, part #TH43001XT-501EX. The…

view full answer...

Answer 2

Usually ladder racks use the inside edge of the top of the bed site to attach to the vehicle, but luckily there are exceptions to that. The Thule TracRac SR is typically compatible with tonneau covers that mount to the inside edges of the truck bed.…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Ladder Rack Compatibility with 2003 Toyota Tundra and BAKFlip Tonneau

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching