Slide Out Awning Cover Recommendation for 8 Foot Wide Flange Width Slide Out

Question

Question:

My slide out is 8’ flange to flange and 90 “ in side flange 36” when in our postion what one do I need and does it come complete kit for mounting

asked by: Perry

0

Expert Reply:

Since your flange width is 96 inches (8 feet) the correct Solera slide out awning you need is the part # LCV000163289 as it has a flange width range of 92" to 97-3/4".

All the mounting hardware is included as well as an awning rail.

expert reply by: Jameson C

0

Answer 1

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 2

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 3

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 4

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 5

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...

Answer 6

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 7

You'd need a new panel like the Progressive Dynamics Mighty Mini part #PD4045KA which is the most similar to your Parallax 7345 except is Lithium battery compatible. There isn't a center section replacement available for what you have that…

view full answer...

Answer 8

Having the extra amperage of the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K has no down side. You'd at worst just have more power available than you'd need.

view full answer...

Answer 9

To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…

view full answer...

Answer 10

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Slide Out Awning Cover Recommendation for 8 Foot Wide Flange Width Slide Out

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching