Will the Replacement Fan Motor Assembly Kit # FVK8017-00 Fit a Fan-Tastic Roof Vent 4000

Question

Question:

1999 Winnebago Adventure 32t fantastic vent 4000 fan replacement dont know if this will work but my motor is fine its the blades that broke

asked by: Richard

0

Expert Reply:

Yes, you can use the Replacement Fan Motor Assembly Kit # FVK8017-00 to replace the broken blades on your Fan-Tastic Roof Vent 4000. Simply remove your whole motor assembly, since the blades are part of it, and connect the butt connectors to the appropriate wires (pay attention to where each wire is connected when removing your old assembly).

expert reply by: Jon G

0

Answer 1

I spoke with my contact at Fan-Tastic Vents and she verified that the part #FVK8017-00 is a replacement for your 4000 can style motor. She said they actually have this listed as a fit in their system so you are good to go!

view full answer...

Answer 2

Yes, the Replacement Fan Motor Assembly Kit #FVK8017-00 is the correct motor replacement for your Fan-Tastic 4000BT roof vent.

view full answer...

Answer 3

Thanks for the picture of your roof vent. From that I can tell that the motor part #FVK8017-00 that you referenced is the correct replacement.

view full answer...

Answer 4

Yes, we do sell a replacement switch for the Fan-Tastic roof vent. The 3-Speed Switch for Fan-Tastic Vent Roof Vent item #FVK1031-05 replaces the 3-way switch in your vent.

view full answer...

Answer 5

You can use part #FVK8017-00 to replace the bow-tie bracket, motor, and fan blade for your Fan-Tastic Vent 4000-series roof vent.

view full answer...

Answer 6

If everything else is working on your Dometic FanTastic Roof Vent w/ 12V Fan and Remote #FV807350 except the fan then either the wiring to the fan is damaged and needs to be replaced, or the motor is bad and you need to replace the assembly with the…

view full answer...

Answer 7

The Valterra Waste Valve Bodies w/ Flexible Cables for RV Black Water and Gray Water Tanks - 72" Item #TC1372 is a correct replacement for your gray and black tank valves. I have attached a picture from the guide to help with placement of the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Will the Replacement Fan Motor Assembly Kit # FVK8017-00 Fit a Fan-Tastic Roof Vent 4000

Product Page this Question was Asked From

Continue Researching