Electric Lockout Solenoid Wiring

Question

Question:

Why 2 wires out of the back of the lockout solenoid? Thanks

asked by: Andy P

1

Helpful Expert Reply:

The two wires coming out of the Titan Zinc-Plated Brake Actuator w/ Drop, Electric Lockout - Disc - 2-5/16" Ball # T4750620 are for the lockout solenoid as you stated. One wire will be used for the power coming from your reverse light signal and the other will ground to your trailer frame.

Some of the models now come with a single wire for power on that solenoid and have a set screw underneath to attach your own ground wire to the frame.

expert reply by: Jason S

1

Answer 1

We have the Titan version of the coupler you need as Titan Weld-On Coupler part #T1755000 which fits a 3 inch channel and is designed for a 2-5/16 inch hitch ball too.

view full answer...

Answer 2

Getting your tongue weight to be 10 to 15 percent of the total trailer weight will have the greatest impact in reducing the sway of the setup. Also having the trailer as level as possible will help too. For a trailer that weigh 6,500 lbs the Reese…

view full answer...

Answer 3

I would be happy to help! I attached a help article for you to check out that details exactly how the P3 Brake Controller part #90195 will install in your 2014 GMC Yukon, but basically here is how the wires will attach. Red/Black from Yukon to Black…

view full answer...

Answer 4

If you are absolutely sure you'd never be over the 12k number you listed a 12.5k actuator like the Demco part #DM8104311 would work great. I really like how easy to use the EZ latch couplers are of the Demco actuators. If you wanted extra…

view full answer...

Answer 5

The Master Lock Trailer Coupler Lock #377DAT you purchased can accommodate a max coupler width (including lip) of 4 inches , so for a lock that works with up to a 4-3/4 inch coupler width, I recommend the Blaylock EZ Lock Trailer Coupler Lock…

view full answer...

Answer 6

I can certainly understand not wanting to have to connect 2 five-foot carpeted bunk rails like #CE27820 to get the 10 foot bunks you need. We don't offer them in the 10' length because the shipping costs would be more expensive than the bunks…

view full answer...

Answer 7

If the hub bore is 1.5 inches like you mentioned (the area of the hub where the cap installs) then we don't have a Bearing Buddy that will fit. If the measurement was more like 1.75 inch then the #BB1781 would most likely fit as it measures 1.78…

view full answer...

Answer 8

The master cylinder assembly on the Titan model 20 actuators, like #T1521000 as an example, is bolted to the inside of the actuator. Take a look at the picture I have included as an example. There are 2 bolts on each side holding in the assembly.…

view full answer...

Answer 9

I reached out to Demco for you on the Demco Hydraulic Brake Actuator with Drop and Electric Lockout part #DM8104311, they informed me that the distance from the center of the rear mounting hole to the end of the casing is 7-3/4". I have attached…

view full answer...

Answer 10

We have not yet replaced the Shock part #T1242600 on a Titan Model 10 Surge Brake Actuator so I do not have any specifics for you but I have attached a parts diagram which shows you how the unit is broken down. You can then use this to get a better…

view full answer...

Answer 11

It's not needed to glue the bunk board carpet like #CE11349 as well as staple it. With just staples you'd be fine.

view full answer...

Electric Lockout Solenoid Wiring

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching