Gauge Wire Used in the 2-Wire Pigtail for Optronics Trailer Lights # A45CB

Question

Question:

Im preparing for an install of an Optronics light that features a backup light and intend to use the 2-wire pigtail part number: A45CB to attached to the reverse circuit. Can you clarify the wire size used on this 2-wire pigtail? Thanks,

asked by: Bill G

0

Expert Reply:

The gauge of wire in the 2-Wire Pigtail for Optronics Trailer Lights # A45CB is 18 gauge.

expert reply by: Jameson C

0

Answer 1

You are correct, that is exactly how you would install that setup. To add reverse lights to your trailer from a 4 pole to a 7 pole on your 2017 Ram 1500 you are going to need a junction box with a 7 pole connector. I recommend is the Trailer Wiring…

view full answer...

Answer 2

You'd really want to use a 3-to-2 wire converter such as the Roadmaster #RM-732 to convert the separate wiring on your 2010 Nissan Frontier to a 2 wire system like the #STL1211RCFHPG you were looking at is designed to work with. This will make it…

view full answer...

Answer 3

So in order to add a reverse light to your boat trailer, all you need to do is connect the wiring from your junction box or 7-way directly to the reverse light's wires. For reverse lights, if you don't already have wiring at the junction box…

view full answer...

Answer 4

In order to add reverse lights to a trailer would would need to have a 7-Way on the trailer, like #50-67-103, and a 7-Way on the vehicle. On the vehicle side, if you are looking at the back of the 7-Way where the wires connect, the reverse light…

view full answer...

Answer 5

The center pin on the 7-way trailer connector carries the reverse lamp signal. Install your reverse lamps such as #BUL10CB as well as the #A45CB pigtail and the #A70GB grommet and #BK70BB bracket if needed. Then, run a length of #DW02359-1 16 gauge…

view full answer...

Answer 6

We can get you set up to add back up lights and a 7-way to your boat trailer, and I'll go over what you'll need. Let's start with the back up lights, and for your boat trailer you'll want submersible lights like you said, the GloLight…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Gauge Wire Used in the 2-Wire Pigtail for Optronics Trailer Lights # A45CB

Product Page this Question was Asked From

Continue Researching