Replacement Air Spring For Custom Build Ice Shanty

Question

Question:

Does do you have it in a kit form?

asked by: Steve S

1

Helpful Expert Reply:

The tallest air spring we carry is the Firestone Rear Air Spring # F7076 which has a compressed height of 3.95 inches and an extended height of 10.5 inches. The rest of the height you require would need to be determined by the brackets you use on your custom application.

expert reply by: Jason S

1

Steve

4/23/2018

Does do you have it in a kit form?

Reply

Jason S.

4/25/2018

Unfortunately we don't have a kit specific to that part. The kit it belongs to is F2171 which has been discontinued. Another option is the Firestone Rear Air Spring, Tapered Sleeve, 1/4" NPT - Model 110/70 # F9001 which has a compressed height of 4.37 inches and an extended height of 8.37 inches. It operates between 5 psi and 100 psi. Unfortunately the kit for that spring has also been discontinued.

Reply

Answer 1

The Firestone Ride-Rite Air Helper Springs - Rear Axle #F2709 referenced in your question is confirmed to fit your 2017 Chevy Silverado 3500. We have spoken to Firestone before and they state that on trucks that have just a 1 inch rear lift, a spacer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Replacement Air Spring For Custom Build Ice Shanty

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching