How to Measure to Pick Out Replacement Axles for a Trailer

Question

Question:

I have a al ko axis axle on my 6-12 single axle. The axle has the following P/N: 1453139 then next to that is has: D35B UL FL 85/70/73.25 BM FC 5451 the following line has: 8103r . It has a drop axle in it I would like to change to a straight axle to raise it up. Can you tell me what model axle I would need? Thank You

asked by: Bob M

1

Helpful Expert Reply:

You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference.

You will need to measure from hub face to hub face and then from the spring seat centers. You will also need to know what bolt pattern you have on your current hubs. I attached a help article on how to determine this as well.

I also attached a link to a page with all of the axles we carry.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How to Measure to Pick Out Replacement Axles for a Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching