Replacement 7-Way and Wiring Harness for 2012 Ford F-250

Question

Question:

Will the wiring harness with cannon plug connect to the factory installed 7- and 4 Pole trailer Connector Socket?

asked by: Rodgfer W

1

Helpful Expert Reply:

The Hopkins Endurance Quick-Install 7-Way Trailer Connector with Universal Pigtail Harness # HM47210 would work well for you if you somehow damaged the wiring harness of your 2012 Ford F-250 and need a new connector with wiring and a new 7-way.

I attached an install video for this kit on a similar Ford truck as yours as well.

expert reply by: Jameson C

1

Answer 1

Since you are not getting the 12V power when your truck is running, you most likely don't have a fuse issue as you stated their isn't a specified fuse or relay in the owners manual. The issue is that your truck is computerized even at the…

view full answer...

Answer 2

I went out to the warehouse and pulled Hopkins 7-Way #HM47210 from the warehouse to measure it for you. From side to side the mounting holes are 2-1/4 inches apart on center. And from top to bottom they are 1-1/2 inches apart on center. I have…

view full answer...

Answer 3

Yes, what you described is very common and would work well. The part #HM47210 that you referenced can have it's 12 volt power circuit wire ran to a trailer battery that is powering an electric tongue jack. People do this all the time and it works…

view full answer...

Answer 4

If all the fuses and relays appear to be in good shape on your 2012 Ford F-250, then it's possible that there is an issue with the wiring behind the trailer connector. I recommend first simply inspecting the connector itself for any corrosion and…

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 8

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 11

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement 7-Way and Wiring Harness for 2012 Ford F-250

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching