What Is Needed To Replace An Old Axle With A New Axle
Question:
I am thinking about replacing the full axle assembly on my Haul Master trailer Model 90154. My question is how much custom fabricating will I need to do. Will it be a simple remove the old axle and bolt on the new? Or will I have to custom fit the suspension somehow. The part number for the axle I am interested in is # 20440I-EZ-60.
asked by: Frank
Expert Reply:
The Dexter Trailer Idler Axle Kit, Item # 20440I-EZ-60, includes most of what you need to complete the axle change and installation. It has a 2,000-lbs weight capacity and is fairly easy install (see attached video). I also encourage you to double-check your measurements to make sure you are getting the right kit for you and your trailer.
This Dexter kit will include a straight trailer axle that measures 60 inches from hub face to hub face and 48 inches from spring center to spring center. It also has idler hubs with bearings, races, seals. It also comes with EZ-Lube spindles. While changing everything, I also recommend getting a new u-bolt kit like the U-Bolt Kit for Mounting Round Trailer Axles, Item # APUBR-10. You will need to measure from the bottom of the cross member to the bottom of the bolt posts to make sure a good fit (see attached picture and video).
I am attaching additional information and videos to assist you with your axle project.
Products Referenced in This Question
U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4-1/4" Long U-Bolts
- Trailer Suspension Parts
- U-Bolt Kits
- Camper
- Car Hauler
- Utility Trailer
- 2000 lbs
- Round Axle - 1-3/4 Inch
- 3/8 Inch Diameter
- 4-1/4 Inch Long
- Dexter
more information >
Product Page this Question was Asked From
Dexter Trailer Idler Axle w/ Idler Hubs - EZ-Lube - 4 on 4 Bolt Pattern - 60" Long - 2,000 lbs
- Trailer Axles
- Leaf Spring Suspension
- Easy Lube Spindles
- Idler Hubs
- 2000 lbs
- 4 on 4 Inch
- 48 Inch Long
- 60 Inch Long
- No Drop or Lift
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Dexter Trailer Idler Axle w/ Idler Hubs - EZ-Lube - 4 on 4 Bolt Pattern - 60" Long - 2,000 lbs
- Search Results: boat trailer rollers
- Shop: Yates Spool Roller for Boat Trailers - TPR - 5" Long - 1/2" Shaft
- Shop: U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4-1/4" Long U-Bolts
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Video: Yates Rubber Boat Trailer Parts - Roller and Bunk Parts - YR510Y-4 Review
- Shop: Boat Trailer Guide-On Roller, 2" Diameter x 9" Long by Dutton-Lainson
- Shop: Roller Shaft with Pal Nuts for Boat Trailer Rollers - Zinc-Plated Steel - 5-1/4" x 1/2"
- Search Results: boat roller
- Article: Trailer Wiring Diagrams
- Search Results: trailer leaf springs
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: leaf spring
- Shop: Trailer Hitch
- Article: Trailer Tire Sizing
- Search Results: axle
- Q&A: Picking Out Hubs and Brake Assemblies for Tandem Axle Trailer that Weighs 6k
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: etrailer Trailer Leaf Springs Review
- Q&A: What Is Needed To Replace An Old Axle With A New Axle
- Search Results: leaf springs
- Article: How to Accurately Measure Trailer Leaf Springs
- Shop: Suspension Enhancement
- Search Results: equalizer
- Shop: Roof Rack
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Trailer Suspension Parts
