Weight Of B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit

Question

Question:

What is the total weight added to the truck with this setup? Thanks

asked by: Cecil

0

Expert Reply:

The B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit # BWGNRK1313 shipping from etrailer at a weight of 112 lbs. It will be a little less weight than that because of the shipping materials, but not by a lot.

expert reply by: Timothy G

0

Answer 1

It sounds like you're trying to add a gooseneck hitch to your 2008 Dodge Ram 2500 with an 8-ft bed, and we have just what you're looking for. I recommend using the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1313,…

view full answer...

Answer 2

I confirmed with my contact at B&W that the B&W Turnoverball Gooseneck Hitch #BWGNRK1313 you were looking at will fit your 2013 Ram 2500 Diesel 4WD with the Ram Box perfectly. You can tow a gooseneck hitch with no problems, but the…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Answer 6

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

There's a few differences. • The Curt #C31017 is manufactured in the US, while the Draw-Tite #65046 is manufactured in Mexico. • When installed, the Curt hitch will sit higher on the vehicle for more ground clearance. The underside of the…

view full answer...

Answer 10

Let's start at the brake assemblies/hubs on your new gooseneck trailer. The two wires coming from each assembly look exactly as they should. One wire will ground to the trailer frame and the other wire will attach to the brake output wire. The…

view full answer...

Answer 11

You could certainly use Opti-Brite LED work light #TLL48FB on your horse trailer and put it on a switch but having it wired into the running light circuit could have some unintended issues. Specifically, if you forgot to turn the switch off and drove…

view full answer...

Answer 12

Your slide-in truck camper does not have electric brakes so the blue brake circuit wire from its 7-way connector is not used. All other lighting functions as well as 12V auxiliary power will be maintained on the other circuits. Please refer to the…

view full answer...

Weight Of B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching