Cushioned Pin Box to Reduce Chucking on 2008 Keystone Raptor 3600RL

Question

Question:

I currently have a MOR/ryde RPB72-1116installed on my 2008 Keystone Raptor 3600RL pin weight is 2855 lbs Gross weight is 16,500 lbs would i see much difference in the chucking if i installed the Trailair Air Ride pin box or am i wasting my money Thanks

asked by: Harry C

0

Expert Reply:

The best pin box replacement we offer for your 2008 Keystone Raptor 3600RL is going to be the Trailair part # LC155943 which has two ways to cushion the ride of the trailer.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Thank you for the photo of your Lippert pin box. You have their model 1116. I confirmed this with my contact at Lippert. The Trailair Air Ride 5th Wheel Pin Box #LC155943 that you referenced is a direct bolt-on replacement for the 1116. It comes…

view full answer...

Answer 2

When installed the Trailair Flex Air 5th Wheel Pin Box #LC328492 only requires 4 bolts to be ran through the pin box and the trailer frame. I attached a picture that shows this pin box installed on a similar trailer and that it only uses 4 bolts. So…

view full answer...

Answer 3

If you have no identifiers on your 2016 Keystone Cougar 333MKS then the only way to determine the bolt pattern of your pin box is to either contact the manufacturer with the frame number, which is usually extremely time consuming, or to use our guide…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 8

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 9

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 10

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 11

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Cushioned Pin Box to Reduce Chucking on 2008 Keystone Raptor 3600RL

Product Page this Question was Asked From

Continue Researching