Replacement 7-Way and Wiring Diagram for Camper

Question

Question:

Someone cut the pigtail off my camper where you plug into the bumper of the vehicle for the brake lights ,marker lights ,etc of the camper to work . How can I get a schematic to camper for the correct wiring of a 7 pin connector ?

asked by: Hubert C

0

Expert Reply:

Sorry to hear about the vandalism of your camper. I attached a couple diagrams for 7-way trailer wiring harnesses. For a replacement 7-way we have the part # H20042 which comes with 3 feet of wire.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The 7-Way Molded Trailer Wire Connector - 3' Long #H20042 has different wiring colors than other connectors. The color that will connect to the reverse light function is the yellow wire of this molded connector. They label it Aux as some people…

view full answer...

Answer 2

Your ST225/75 R15 wheel and tire combo is well below the size and weight limit for the Fulton Hi-Mount Spare Tire Carrier #FHDSTC0101 so it should work well without you having to worry about it failing. I attached a review video for this product for…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 10

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Replacement 7-Way and Wiring Diagram for Camper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching