Does Reese Fifth Wheel Ford Rail Kit Adapter RP60156 Fit Valley 7054 Slider Hitch

Question

Question:

Is the valley 7054 or CP 7054 a sliding hitch ? Also is it compatible with the Reese R.P. 30156 adapters and will the rp30156 fit a 2015 Ford 350 with factory pre install kit

asked by: Tom C

1

Helpful Expert Reply:

The Valley 7054 hitch is pretty old so info on it is harder to come by, but we do know that it is a slider hitch and that it fits the rails that the Reese adapter part # RP30156 provides.

So if you have a 7054 hitch and a Ford truck with the factory rail kit the # RP30156 would be the correct kit you'd need.

expert reply by: Jameson C

1

Answer 1

Fifth wheel hitches can be pretty tall. Especially if you use a rail kit adapter like the #RP30156 which will add 2-3/4 inches from the floor of the truck bed to the top of the rail kit adapter. Most likely your Pullrite is going to sit too tall to…

view full answer...

Answer 2

If your SuperGlide will work with industry standard fifth wheel rails that are 22 inches apart then the #RP30156 adapter will work for you. Some of the Pullrite hitches only fit their rails and adapters so if that is the hitch style you have then…

view full answer...

Answer 3

Yes, the Reese Elite Series Underbed Rail Adapter for Standard 5th Wheel Trailer Hitches #RP30156 will work with your Reese Pro Series 5th Wheel Hitch! I have attached a quick installation video for you to check out as well.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 10

For an above bed rail kit that fits your 2017 Ford F-250 you can use the B&W Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches #BWRVK2402. These are industry standard rails (ISR) that are compatible with B&W Patriot, Curt,…

view full answer...

Answer 11

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 12

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Does Reese Fifth Wheel Ford Rail Kit Adapter RP60156 Fit Valley 7054 Slider Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching