Replacement Tarp for TruXedo Tonneau Cover on 2003 Ford Ranger Flare-Side Bed

Question

Question:

Hello - Can you please confirm that Item # TX2471-CVR is the Truxedo replacement cover for FLARESIDE Ford Ranger? Not the standard bed. Thanks.

asked by: Rick S

0

Expert Reply:

We have TruXedo brand tonneau covers to fit your 2003 Ford Ranger with 6-foot flare-side or step-side bed, the TruXport # TX247101 and Lo Pro QT TX547101.

The part you referenced, Replacement Cover # TX2471-CVR, is the correct part if you have the TruXport cover.

If you have the Lo Pro QT then instead use # TX5471-CVR.

expert reply by: Adam R

0

Answer 1

From what I can see I believe you either have the TruXedo Pro X15 #TX1446601, which has a matte black finish, or the TruXedo Lo Pro QT #TX546601, which as a gloss black finish. If your cover has a matte black finish then that means you have the Pro…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Replacement Tarp for TruXedo Tonneau Cover on 2003 Ford Ranger Flare-Side Bed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching