Bike Rack Recommendation for 1 Electric Bike

Question

Question:

I am looking at getting an Electric bike... most weigh around 60 lbs. Im short and a gal so lifting this will be a bit of an umph. I really only need one bike mount. Can the outside bike holder be taken off the hitch completely in order to help me put the bike onto the rack closer to the vehicle. Thanks

asked by: Lynne

0

Expert Reply:

I have a solution for you. Take a look at the RockyMounts HighNoon FC Solo Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount # RKY87RR. It is designed for just 1 bike and has a capacity of 60 pounds. I have included a link to a video review of this rack for you.

expert reply by: Michael H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack…

view full answer...

Answer 5

You could leave off installing the outside wheel clamp of the RockyMounts WestSlope bike rack part #RKY10222 but you can't shorten the frame of the rack where the wheel mounts are. For a bike rack with a smaller footprint that can carry up to…

view full answer...

Answer 6

Hello again Michelle. The Saris Glide EX Bike Rack #SA774 will indeed fit a 2023 Hyundai Tucson with a class 3 hitch. The tilt feature will allow the hitch to open and close normally. Saris bike racks are definitely good quality. They are all made…

view full answer...

Answer 7

Either the Kuat Tranfer 1 #KU64FR or the RockyMounts MonoRail Solo 1 #RKY10007 would handle the bikes you describe easily. Both would hold the bikes by the tires, so the fact that the rack won't come into contact with the frame will work…

view full answer...

Answer 8

The Tow Defender #RM-4700 you found is really our best option to protect the front of your 2024 Chevrolet Trax. This screen helps to deflect any road debris back down to the ground to keep it traveling under your Trax. This particular cover is…

view full answer...

Answer 9

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 11

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Bike Rack Recommendation for 1 Electric Bike

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching