Replacement Foot Pads for 2012 Heartland Elkridge 5th Wheel Trailer

Question

Question:

Can this replacement foot pad fit a 2012 Heartland ElkRidge 5th Wheel?

asked by: Tim S

0

Expert Reply:

The Lippert foot pad # LC314667 is a 9 inch diameter pad that is a fit for the automatic leveling systems. You may alternatively be interested in the rear foot pad # LC377962 or the front foot pad # LC362486. You may also want the Replacement 3/8" x 3" Snapper Pin # LC225598.

If you do not have the Ground Control Auto Leveling system, then I recommend the Replacement Footpad and Pin for Stromberg Carlson Landing Gear # LG-119225 which fits most other landing gear system. The pad gives you an 8 x 5 inch support.

expert reply by: Jason S

0

Answer 1

It is possible that there is a part number somewhere that would help identify the landing gear on your trailer. Sometimes there is information on the underside of the caps on the tops of the jacks so that is another place you can check if you…

view full answer...

Answer 2

The SnapPad Jack Stand Pads like part #SP54FR4 may still work with the Steady Fast or JT Strong Arm Stabilizers but you'd likely need to trim the pad where the arm attaches or raise the arm up a bit from the pads. There is a lip on the pads…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, you will need a spacer. The Air Lift LoadLifter 5000 Air Helper Springs item #AL57341 are designed for the stock height on your 2024 GMC Sierra 2500. Which spacer you need is going to be determined by how big of a lift you actually have in the…

view full answer...

Answer 7

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The Gen-Y Hitch 5th Wheel to Gooseneck Pin Box item #GY98GR weighs a hefty 120 lbs. This is the only way to add a gooseneck pin box to a 5th wheel trailer with a Rhino Box. You will also need the Safety Chain with 2 Hooks item #GY49GR. State laws…

view full answer...

Answer 10

The overall height of the Timbren Spring Kit part #TGMRCK25D is 6-1/4 inches.

view full answer...

Answer 11

You will actually be needing the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness #HM54FR for your 2021 Chevrolet Silverado 2500HD. This will ensure you have the correct wiring and length needed to install in your truck bedside. The…

view full answer...

Answer 12

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...