Removing Factory Suspension Bump Stops on 2011 Chevy Silverado to Install Timbren Rubber Springs

Question

Question:

I cant seem to be able to pry the factory bump stops out of their mounting cups. Is there a technique to doing this

asked by: Maurice D

0

Expert Reply:

The bump stops are compression fit into the cups on the truck frame, therefore they aren't designed to come out easily.

I have spoken with one of my contacts at Timbren, who tells me that the bump stop can be removed with a pair of channel lock-type pliers. Grasp the bump stop with the pliers and pull down on it while twisting back and forth.

In case you do not have them handy, I have provided a link to the install instructions.

expert reply by: Mike L

0

Answer 1

You could go with the Lippert 2" Trailer Hitch Receiver for Campers and Trailers #LC730647 you were looking at, but because this only hitch has a 300-lb tongue weight rating I believe there is a better solution. I recommend going with the Curt…

view full answer...

Answer 2

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Removing Factory Suspension Bump Stops on 2011 Chevy Silverado to Install Timbren Rubber Springs

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching