Recommended Trailer Jack for 2017 Sure Trac Dump Trailer

Question

Question:

I have five 2017 Sure Trac Dump Trailers that I need to replace the landing/jack leg. I need side wind. Model # of the Trailer: ST8214DDB140 Thank you in advance

asked by: Kharnest

0

Expert Reply:

For your 2017 Sure Trac Dump Trailers, I recommend the Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs # TJA-5000S-B. Then you can add the footplate # JF-99 or a Drop Leg # JF-1005H-Z.

These jacks are very well made and have a high tongue weight load capacity of 5,000 lbs.

expert reply by: Jason S

0

Answer 1

We have a drop leg that fits your Lippert powered a-frame jack with the #LC405217 but the part number you mentioned fits a different brand and would not work.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 8

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 9

Hey Ted, so if you look in the bed of your truck and see 5 holes/pucks that would mean you have the OEM prep. I'd assume if you had it you'd have seen them by now. If you had it you'd only need a ball like the part #C60618. If you…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 12

Yes, we do! It is Curt Custom Underbed OEM-Style Gooseneck Hitch item #C60633. This gooseneck hitch is confirmed to fit both the 6-1/2' and 8' bed lengths of the new 2024 Ram 2500. It has a massive 35,000 lbs capacity and installs in…

view full answer...