Ladder Rack for a 5 x 8 Round Top Carry On Patriot Enclosed Trailer

Question

Question:

Hello I want a roof rack for my small cargo trailer and not sure what my options are. It is a Carry On Patriot 5X8 round top.. I think Id like to put 3 bars across... Thanks

asked by: Mike D

1

Helpful Expert Reply:

The best option is the Rack'em Fitz-All Enclosed Ladder Rack, part # RA-28. This rack installs to the top of your trailer's side walls and telescopes to fit up to an 8-1/2 foot trailer with its telescoping design. The kit is capable of holding up to 400 pounds, and is a relatively quick install.

The only downside is that the kit is sold in sets of two, and single racks aren't available.

I've included a video that details the rack's installation onto a trailer so you can get familiar with the installation process.

expert reply by: Jacob W

1

Answer 1

The Rack'em Fitz-All Enclosed Trailer Ladder Rack #RA-28 has a 400-lb total weight rating for its two adjustable crossbars so I would expect that it will be up to the task of handling your extension ladder. As a check I looked into the weight of…

view full answer...

Answer 2

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 3

The tires on your trailer should not come off the ground while leveling. It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix…

view full answer...

Answer 4

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 5

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Answer 6

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Answer 7

There are going to be two parts to the handle that you will need to operate the Lippert Components Spare Tire Winch part #LC159056. The first of which is the intermediate shaft or what Lippert calls a Crank Extension part #LC1315411. This will be…

view full answer...

Answer 8

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 will not have any locking or hold mechanism short of being completely reeled in. I spoke to my tech contact at Lippert who has this on his truck and he said you just crank it up…

view full answer...

Answer 9

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 requires the handle #LC119226 to crank up and down.

view full answer...

Answer 10

To raise and lower the Lippert Spare Tire Winch with Offset Cable #LC159056 what you need is the replacement manual crank handle part #LC119226.

view full answer...

Answer 11

It is possible to over-fill a hub that has a Bearing Buddy bearing protector such as #BB1781. The convenience of easy filling through the zerk fitting can often mean we can be tempted to keep adding more grease. ("If a little is good, then more…

view full answer...

Answer 12

Yes, you can replace your GE air conditoner with an Advent air conditioner like the Advent Air RV Air Conditioner #ACM150. Additionally, you will also need a thermostat. For that, you can use the Air Distribution Box w/ Built-In Thermostat for Advent…

view full answer...