What are the CE Smith Carpeted Bunk Boards # CE27810 Made of

Question

Question:

What are these made out of?

asked by: Daniel

0

Expert Reply:

The CE Smith Carpeted Bunk Boards # CE27810 that you referenced are made of exactly that; wooden boards.

They do have a marine-grade black carpeting with velvety finish that is strong, soft and weather resistant to keep them in good shape. They also have a copper-free construction which is safe to use with aluminum and steel boats.

I have attached a sample installation video for you to check out as well.

expert reply by: Jon G

0

Answer 1

The 3 inch rubber bow roller, #YR3143-4, that you referenced is typically used at the front of the boat near the winch. The rollers that are usually used in the middle and rear are keel rollers. Often times, the v shape of the 3 inch bow roller is…

view full answer...

Answer 2

We don't have 2x6 bunk boards that are 4 feet long, but we do have 2x4 carpeted bunks that are 4 feet long. For that you would want the part #CE27810. I attached an install video for you to check out as well.

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

What are the CE Smith Carpeted Bunk Boards # CE27810 Made of

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching