Edge Programmer and Power Gains for 2018 Ford F-150 with 3.5 liter EcoBoost

Question

Question:

Is the EP59YR programmer compatible with my truck and what HP and Torque gains can I expect?

asked by: Josh P

0

Expert Reply:

For your 2018 Ford F-150 Lariat V6 3.5 liter ECOboost the Edge Programmer part # EP59YR is a confirmed fit.

According to Edge's website the highest power level will get you 86 horsepower and 63 ft lbs of torque. That's quite a bit and something you definitely would feel.

expert reply by: Jameson C

0

Answer 1

No, you will not need to adjust the gear ratio setting on the Edge Evolution Programmer part #EP59YR when changing from the factory tire size. The gear ratio setting should only be changed if a different ratio ring and pinion set has been installed…

view full answer...

Answer 2

Before you traded your truck in you should have uninstalled the Edge Gas Evolution CTS3 Performance Tuner - Color Screen #EP59YR from the vehicle. This programmer can only be installed onto one vehicle at a time. If you didn't remove the tune…

view full answer...

Answer 3

I recommend going with the Black Armour Heavy-Duty Custom Truck Bed Mat #BA37AR for the 6-1/2' bed on your 2023 Ford F-150 because it's a 1/2" thick vulcanized rubber mat that does a great job protecting your truck bed. I really like the…

view full answer...

Answer 4

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Edge Programmer and Power Gains for 2018 Ford F-150 with 3.5 liter EcoBoost

Product Page this Question was Asked From

Continue Researching