Replacement Actuator Recommendation for GDC Surge Actuator

Question

Question:

I have a GDC 80 actuator that needs the Master Cylinder replaced. With GDC out of business are there parts available or will i need to replace the entire unit?

asked by: DAVE T

1

Helpful Expert Reply:

Since we don't carry any master cylinders that are a fit for the GDC brand the best solution we'd have would be to replace the entire actuator.

Your picture is a bit fuzzy, but the best match we have is the Demco Actuator part # DM8609502 which fits the standard 50 degree angle A-frame trailer.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The Titan Surge Trailer Actuator part #T4747220 will pretty easily install in place of what you have now but looking at the picture of what you have and what looks like an equal distance between the mounting holes it would seem most likely that you…

view full answer...

Answer 2

We have the perfect replacement for your Global Direct GDC-80 brake actuator. Since you mentioned "down tongue" I believe you were referring to having an actuator with drop. If you have disc brakes, the best option is the Demco Hydraulic…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Replacement Actuator Recommendation for GDC Surge Actuator

Product Page this Question was Asked From

Continue Researching