Kodiak Caliper-Mounting Guide Bolt Replacement Sleeve for Model 250 Caliper

Question

Question:

#K225SS Is this the right Sleeve for the Kodiak 250 brake caliper?

asked by: Dan B

0

Expert Reply:

Yes, you can use Kodiak Caliper-Mounting Guide Bolt Replacement Sleeve # K225SS for your Kodiak model 250 disc brake calipers. I confirmed with Kodiak that this is the correct part.

All Kodiak disc brake caliper replacement parts are shown on the linked page.

expert reply by: Adam R

0

Answer 1

The Kodiak Disc Brake Kit #K2HR858DE is able to be used as a grease lube hub or a oil lube. The Bearing Kit #DBRKHW850 will provide you with bearings, oil seals and lug nuts needed for the Kodiak kit to use as a oil bath hub. The Kodiak Synthetic…

view full answer...

Answer 2

I spoke with my contact at Kodiak and he said Amsoil Severe Gear 75W-140 would be acceptable on their oil bath hubs. When filling the hubs, you will want to remove the rubber plug from the oil cap and fill the hub to the bottom of the hole. When…

view full answer...

Answer 3

The difference between the two replacement oil batch hub caps you referenced part #KPCAP and #XL-PLCAP is the size of hub they are designed to fit.

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Kodiak Caliper-Mounting Guide Bolt Replacement Sleeve for Model 250 Caliper

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching