Amperage Draw of the Kat's Magnetic Heater Part # KH1190

Question

Question:

Do you know how many amps this draws? I want to run 2 off of 1 110v-20 amp circuit.

asked by: Lee

0

Expert Reply:

I spoke to my contact at Kat's and they informed me that the Kat's Heaters Handi-Heat Magnum Magnetic Heater part # KH1190 draws about 3 amps of current.

expert reply by: Conner L

0

Answer 1

I checked with Kat's and the Kat's Heaters Custom Fit Engine Block Heater part #KH11812 is correct for your 2011 Hyundai Sonata with the 2.4L I4 Engine. The block heater will be installed on the front left side of the engine (see…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 5

The Kat's Heaters Handi-Heat Magnetic Heater #KH1155 is usually installed onto the oil or transmission pan to keep the fluid warm. Nothing will need to be cut for use. It's also intended to heat small engines like that of a snowblower…

view full answer...

Answer 6

You will need the Kat's Heaters Custom Engine Block Heater #KH11484 for your 2015 Chevrolet Silverado 1500 with the 5.3L engine. This will install in the block below the #1 cylinder spark plug location. Be sure to get a Kat's Heaters…

view full answer...

Answer 7

The Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts #KH11813 is a confirmed fit for the 3.5L V6. You should not need to alter the element or clip in any way and doing so is not recommended. You may want to…

view full answer...

Answer 8

I went out to our warehouse and measured the dimension of the Dexter Replacement Magnet for Dexter 12-1/4" Electric Brake Assemblies, #BP01-306. The magnet measured 4 inches long x 2-1/2 inches wide. This magnet is designed to replace the…

view full answer...

Answer 9

For your Kubota Tractor, I recommend looking at a magnetic heater like the Kat's Heaters Handi-Heat Magnum #KH1190. This particular heater will magnetically attach to the tractor's oil pain, warming the fluid in your engine block for…

view full answer...

Answer 10

We've had this question before and the manufacturer of the ThermaHeat #277-000164 that you referenced has stated that it's okay to insulate over the heating pad.

view full answer...

Answer 11

If the tank heating pads are the correct dimension they will work great and would not overheat them. So if the part #277-000164 fits dimensionally it will work great.

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Amperage Draw of the Kat's Magnetic Heater Part # KH1190

Product Page this Question was Asked From

Continue Researching