Correct Block Heater for a 2011 Hyundai Sonata with 2.4L I4 Engine

Question

Question:

I have the sonata 2.4 and 2011

asked by: Zia-ur- R

0

Expert Reply:

I checked with Kat's and the Kat's Heaters Custom Fit Engine Block Heater part # KH11812 is correct for your 2011 Hyundai Sonata with the 2.4L I4 Engine. The block heater will be installed on the front left side of the engine (see photo).

expert reply by: Conner L

0

click to enlarge

Answer 1

For your year and model the installation location is at the "front left." I have attached a chart showing this location as well. In the fit guide I put in your vehicle type and in the "Style" section selected the…

view full answer...

Answer 2

I checked with Kat's Heaters and for your 2011 Hyundai Santa Fe with the 3.5L engine the correct Engine Block Heater is part #KH11812. This cartridge style heater will install in the rear right (RR) position on the engine block, which is…

view full answer...

Answer 3

The Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts #KH11815 is a fit for the 3.5 EcoBoost you have. It will fit in the right front location of your engine. You will simply clean the cartridge hole with…

view full answer...

Answer 4

I checked with Kat's and they say that the cartridge heater will install in the front left location of the block. If you check out the chart I attached you can see where you will see where that it is.

view full answer...

Answer 5

I confirmed with Kat's Heaters that the port location for the Custom Fit Engine Block Heater #KH11815 on your 2018 Ford F-150 with the 3.5L V6 EcoBoost engine is on the right front of the block. I went ahead and attached a diagram that shows this…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Correct Block Heater for a 2011 Hyundai Sonata with 2.4L I4 Engine

Product Page this Question was Asked From

Continue Researching