Dimensions of the Curt Universal Bumper Bracket C19748

Question

Question:

can I get dimensions on this?

asked by: William

0

Expert Reply:

You can refer to the linked photo of Curt Universal Bumper Bracket # C19748 for its dimensions. The video I linked for you will also provide useful information about the applications for this item. Installation of this universal-fit item will typically require some modification and/or reinforcement of the bumper.

expert reply by: Adam R

0

click to enlarge

Answer 1

In order to mount the Universal Bumper Brackets for Curt Tow Bar with Adjustable-Width Arms #C19748 to your 2015 Chevy Sonic LTZ, it does require fabrication by way of drilling to accommodate the bolts of the brackets. If you decide to go that route,…

view full answer...

Answer 2

I have attached an image that details the installation process for the Replacement Bumper Bracket Kit #40602 referenced in your question. This bracket kit is designed for use with the Tow Ready #63180 Adjustable Tow Bar along with a couple older…

view full answer...

Answer 3

The Curt Bumper Brackets #C19748 are a universal fit so you do not have to have a special type of bumper. All that is required is a flat metal section of your vehicle's bumper to install the brackets. You can then tow it with Curt tow bar…

view full answer...

Answer 4

So for your 2012 Jeep Liberty, there aren't any base plates that are going to mount to the arms of the Curt Tow Bar with Adjustable-Width Arms #C19745. To continue using that tow bar you would need the brackets it is designed to attach to, which…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...