Replacement Gear Kit for a 7K etrailer Square Direct Weld Jack

Question

Question:

Are the gears replaceable in this jack?

asked by: Kurt B

0

Expert Reply:

Yes, to replace the gears on the 7K etrailer Square Direct Weld Jack w/ Footplate # TJD-8000S you'll need the Replacement Gear Kit # TJD-7000S-GR.

Attached is a video showing how to replace gears for you to check out and use as a reference.

expert reply by: Jon G

0

Answer 1

I do have a possible option for you but the Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks - 3K #TJD-5000-FT only has a capacity of 3,000 lbs so that wouldn't be enough for your dump trailer. The possible option I have is the…

view full answer...

Answer 2

The 8000 Series jack is #TJD-7000S. The replacement gear kit is #TJD-7000S-GR. If you'd like to verify you can measure the gears on your jack. The small gear is 1.331 inches for the outer diameter and 0.505 inches for the inner. Then the large…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 7

Yes, the Sleeve-Lock Trailer Coupler #CTA-196 will fit the channel bracket that comes with the Brophy Lunette Ring w/ 3-Position Adjustable Channel Bracket #BR43ZR. The bolt holes match as well when it comes to size and spacing so you'll be good…

view full answer...

Answer 8

The female version of the Bulldog Replacement Pipe Mount for Swivel Jacks #BDPQM1900 isn't available separately and only comes already installed on the trailer jacks, like what we see with part #BD195362. If you're needing a weld-on bracket…

view full answer...

Answer 9

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...

Answer 10

As far as the labeling of the Kodiak Disc Brake Kit - 13" Rotor - 8 on 6-1/2 - E-Coat - 9/16" Bolts - 8K Dexter Disc Kit #K2R89DDE, Dexter is the parent company of Kodiak. The reason this particular kit calls out Dexter is anything above 7k…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

If you have the ACTH12 then you should also have the Air Distribution Box #ACRG15 which will have a control box for your wiring from the rooftop unit #ACM135 and the thermostat. This air distribution box and thermostat will wire up exactly the same…

view full answer...

Replacement Gear Kit for a 7K etrailer Square Direct Weld Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching