How to Switch Hitch Balls on the B&W Tow & Stow 2-Ball Mount # BWTS10037C

Question

Question:

How do you change the hitch balls?

asked by: Kenneth

0

Expert Reply:

To switch from using the 2" hitch ball to the 2-5/16" hitch ball (or the other way around) you simply need to remove the pin holding it in place, rotate the hitch balls, and then reinsert the pin.

I have attached a review video of the B&W Tow & Stow 2-Ball Mount # BWTS10037C that you can check out where this is done right at the start.

expert reply by: Jon G

0

Answer 1

Yes, you can set the B&W Tow and Stow Ball Mount part #BWTS10033B to 0 rise if you align the adjustable portion of the ball mount with the shank in the drop position. There is not an offset in drop position it starts at 0 and the increments…

view full answer...

Answer 2

Yes, in order to prevent the adjustment pins part #BWTS35010 from being stolen on your B&W Tow & Stow 2-Ball Mount part #BWTS10037C you are going to need a hitch pin lock that has a 5/8" diameter and at least 4-1/2" span. For this,…

view full answer...

Answer 3

Yes, even though the Draw-Tite Max-Frame Trailer Hitch Receiver #76031 only uses 6 bolts as opposed to the 10 bolts for the OEM trailer hitch it has gone through an extensive amount of stress tests to ensure that the 6,000 lb trailer towing rating is…

view full answer...

Answer 4

I really like the Let's Go Aero Anti-Rattle/Lock part #63232. It mounts inside the hollow shank of the ball mount and then holds the ball mount to the hitch tube. It also doubles as a hitch lock to which is a nice feature. I attached an install…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

How to Switch Hitch Balls on the B&W Tow & Stow 2-Ball Mount # BWTS10037C

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching