Recommended Bracket and Roller Shaft For Yates Side Guide Roller 12 Inches Long

Question

Question:

I need the entire bracket for the roller. Mine is welded on with no way to replace just the roller. The new one can be welded on or bolted on no difference. Can you supply?

asked by: Rick

1

Helpful Expert Reply:

The Yates Side Guide Roller for Boat Trailers - Heavy-Duty Rubber - 12" Long - 1/2" Shaft # YR12243-4P is compatible with the CE Smith Side Angle Mounting Brackets for Boat Trailer Rollers - Galvanized Steel - 1 Pair # CE10211G. Then you may be able to use the Roller Shaft with Pal Nuts for Boat Trailer Rollers - Zinc-Plated Steel - 12-3/4" x 1/2" # CE10705A although it doesn't give much space.

A better option is to use the Yates Side Guide Roller for Boat Trailers - Heavy-Duty Rubber - 12" Long - 5/8" Shaft # YR12243-5 along with the One Piece Bracket for 12" Roller for Boat Trailers # 408300, shaft and pal nuts # CE10727A. If you want a split mount, you can use # CE10500G.

expert reply by: Jason S

1

Answer 1

We have the Yates Side Guide Roller for Boat Trailers that are 9" Long with 1/2" Shaft, #YR9202-4. And the 12" Long - 5/8" Shaft Yates Side Guide Roller for Boat Trailers, #YR12243-5. For replacement parts of this type, the…

view full answer...

Answer 2

The best option we have would be the part #YR12243-5. You would need to cut the roller down to the length you need, and the shaft hole will be slightly larger at 5/8 inches than what you currently have. But is a roller with a 2-1/2 inch overall…

view full answer...

Answer 3

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Recommended Bracket and Roller Shaft For Yates Side Guide Roller 12 Inches Long

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching