Threaded Grease Cap Needed with 1.98 inch Diameter

Question

Question:

I am looking for 1.98 inch threaded grease cap. Do you have any?

asked by: Justin

0

Expert Reply:

If you are talking about a grease cap that is compatible with a 1.98 inch hub bore then we an option for you.

The only threaded caps that we have are the Bearing Buddy Bearing Protectors # BB1980T-SS which are stainless steel and come in a pair.

I have attached a review video for you to check out as well.

expert reply by: Jon G

0

Answer 1

I took a look online and the closest thing we have to matching the caps in the vault service kit is going to be the Bearing Buddy Bearing Protectors item #BB1980T-SS. The caps on the bearing buddies will allow your boat trailer wheels to be…

view full answer...

Answer 2

We do have Bearing Buddys with threads on them, but you'll need to verify fitment on your end: Stainless Steel - #BB1980T-SS fits a 1.980" hub bore Stainless Steel - #BB2080T-SS fits a 2.080" hub bore Stainless Steel - #BB2441T-SS fits…

view full answer...

Answer 3

The only sort of grease cap we offer for a threaded 1.98" hub bore is the Bearing Buddy Bearing Protectors part #BB1980T-SS which contains fine threads. This is the only option we'd have save for new hubs as most standard grease caps just…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

A tow package for a vehicle is usually a frame mounted trailer hitch and trailer wiring on a vehicle like your 2002 Dodge Dakota. If you have those two things you could pretty easily assume you have the tow package. Or, you can take the VIN of your…

view full answer...

Answer 9

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Threaded Grease Cap Needed with 1.98 inch Diameter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching