Troubleshooting Hopkins Smart Hitch Grid Lines Display

Question

Question:

I have no grid lines on my monitor for hitch mode or everyday mode. How can I fix this?

asked by: Robert C

0

Expert Reply:

The Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 you will simply press “IN” on the side button and press up or down on the button to activate hitch mode from “OFF” to “ON”. Repeat process to go back to Everyday Mode. I've attached the installation details to assist.

expert reply by: Jason S

0

Ronald F.

6/11/2020

I HAVE A 2006 FORD F150 WITH T.T. I HOOKED UP THE UNIT AND IT WORKED FOR A INSTANCE. NOW NOTHING ???????

Reply

Chris R.

6/15/2020

Is the screen completely black on the monitor? I would just make sure that you're still getting power at the 7-Way. There could be a blown fuse under the hood for the trailer reverse light circuit.

Reply

Robert C.

12/7/2017

I have no grid lines on my monitor for hitch mode or everyday mode. How can I fix this?

Reply

Jason S.

12/7/2017

I reached out to my contact at Hopkins and they said since you don't have grid lines in either mode, there is something internally wrong with the unit. If it is still under the 1 year warranty, they will replace it for you. If not, you will need to purchase another unit.

Reply

Answer 1

Yes, you can splice into the reverse light signal behind your tail light housing and then run this to the 7-way trailer connector. This is how the reverse light circuit will be obtained on any vehicle without tow package wiring for a 7-way.…

view full answer...

Answer 2

I looked up the trailer connector wiring diagram for a 2007 Ford F-250 which should be the same as a Ford F-350 and found the 7-way trailer connector to contain the following wires: Orange = 12 Volt Power White = Ground Black/Green = Reverse Blue =…

view full answer...

Answer 3

Your brake lights and turn signals for each side are on one circuit. The left side turn signal and brake light is generally the yellow wire going into your trailer connector. The first thing to do is check the fuses on your tow vehicle. Next,…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has…

view full answer...

Answer 10

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a…

view full answer...

Answer 12

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...