Height of Timbren Suspension Enhancement Springs with Bracket # TFR250SDJ

Question

Question:

What is the combined overall height of part # TFR250SDJ ? That includes the rubber bumper mounted to the frame bracket.

asked by: Gary

1

Helpful Expert Reply:

The combined height of the Timbren Suspension Enhancement System - Rear Axle # TFR250SDJ is 6-7/8 inches. I went out to our warehouse to measure them for you and also have attached a photo for you to see where the measurement was taken.

expert reply by: Jason S

1

click to enlarge

Answer 1

While we don't currently offer the PD9140 we do carry the 45 amp versions with part #PD9245C for lead acid batteries and part #PD9145ALV for lithium batteries. Since these are rated for 45 amps you will most likely need to increase the gauge…

view full answer...

Answer 2

For rear suspension enhancement that is a confirmed fit for your 2019 Ford F-350 and is also compatible with the in-bed factory rail kit your truck has we have the Timbren kit part #TFR350SDJ which would fit and work well. This gives you the rear…

view full answer...

Answer 3

The U-shaped shims of the Timbren Suspension Enhancement System #TFR350SDJ are designed to help provide a flat mounting surface for the bracket and help stabilize it from left to right. If there's any way you can get the dealer to track them…

view full answer...

Answer 4

The dimensions of the Timbren kit part #TFR350SDJ you referenced are 8-1/2 inches wide by 10-1/2 inches tall by 6 inch diameter. This is a confirmed fit for your 2017 Ford F-350 FX4 and does not require you to use any type of spacers.

view full answer...

Answer 5

All you would need to install the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers #AL88396 on your 2014 Ford F250 with a 3-1/2 inch lift kit is the correct lift spacer kit. For that you would need the spacer kit…

view full answer...

Answer 6

In order to determine if you need to add additional lift spacers to the Air Lift LoadLifter 5000 Air Helper Springs on your Ford F-250 you will need to measure the distance between the upper and lower airbag brackets, then subtract the height of the…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

That's a good question, and we can definitely point you in the right direction for Firestone air bags on your 2021 Ford F-250 Super Duty. The weight ratings are exactly what you said, the amount of weight it can assist up to; so when towing a…

view full answer...

Height of Timbren Suspension Enhancement Springs with Bracket # TFR250SDJ

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching