What Type of Modification is Required to Install Bully Truck Steps # BBS-1103

Question

Question:

Do I have to bend the rocker panel flange on my truck, 2011 chevy silverado 4x4 crew cab to install these steps? If i do, theyre going back.

asked by: Richard P

0

Expert Reply:

To install the Bully Steps part # BBS-1103 there isn't any rocker panel bending required but you do need drill into the lower rocker panel like what you see in the install video I attached.

expert reply by: Jameson C

0

Answer 1

I have a great solution for you but the Bully side steps #BBS-1103 do not fit the 2014 GMC Sierra 1500. They only fit up to 2011 models. But we have other options that do fit your Sierra. I have included a link to the most similar ones for you. I…

view full answer...

Answer 2

There is a spare tire carrier that will work for you, the CE Smith Offset Spare Tire Carrier #CE27310G. This carrier fits trailer frames that are up to 3-1/2" wide x 4" tall and holds 4 and 5 lug trailer wheels (4 on 4" as well as 5 on…

view full answer...

Answer 3

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

What Type of Modification is Required to Install Bully Truck Steps # BBS-1103

Continue Researching