Will Curt X5 Adapter Fit a 2010 Dodge Ram 2500 with B&W Gooseneck Trailer Hitch

Question

Question:

Will this work in a 2010 Dodge Ram 2500 short bed with a BandW hide a ball for a Reese 5th wheel unit

asked by: John T

1

Helpful Expert Reply:

We have not heard of any compatibility issues with the 2010 Dodge Ram 2500 with B&W gooseneck hitch and the Curt X5 adapter # 16310 so you would be good to go. I have linked a video review of the adapter for you.

expert reply by: Michael H

1

Answer 1

It looks like you have the Curt X5 5th Wheel Base Rail Adapter #16310 for B&W Turnoverball Gooseneck Trailer Hiches. A lot of times when the pin isn't quite lining up with the adapter's mounting post it's because of a slight elevation…

view full answer...

Answer 2

The Curt X5 5th Wheel Base Rails Adapter for B&W Turnoverball Gooseneck Trailer Hitches - 20,000 lbs #16310 has a measurement of 14 inches from the front rail edge to the center of the gooseneck. I went to our warehouse to measure it for you.…

view full answer...

Answer 3

Spray in bedliners are not normally an issue for with the Curt X5 adapter part #16310 that you mentioned. Most of the people who use this adapter have one and the adapter itself is height adjustable to compensate for the extra thickness. I attached a…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Will Curt X5 Adapter Fit a 2010 Dodge Ram 2500 with B&W Gooseneck Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching