Diameter of Mounting Holes for Demco Coupler part # DM14793-81

Question

Question:

What grade and size bolts should I use to mount

asked by: Chris

0

Expert Reply:

The mounting holes of the Demco Coupler part # DM14793-81 that you referenced are 1/2 inch in diameter. I'd go with a Grade 5 or higher 1/2 inch diameter bolt and matching nuts and you'd be good.

expert reply by: Jameson C

0

Answer 1

There will be no trailer coupler latch repair kit for an Atwood Trailer Coupler 88555 which is discontinued. Unfortunately, the only option is a full replacement for which I recommend the Demco A-Frame Trailer Coupler part #DM14793-81. This coupler…

view full answer...

Answer 2

Atwood is no longer in business, and because repair kits and replacement parts are manufacturer specific, the best option available is going to be a replacement A-frame coupler. While I'm sure this isn't the news you wanted to hear,…

view full answer...

Answer 3

Yes, you can remove your weld-on coupler and install a new bolt-on coupler that fits a 2 inch ball. There is just a few things you need to do to before and when installing. You need to know what channel size and the weight capacity you will need for…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Diameter of Mounting Holes for Demco Coupler part # DM14793-81

Product Page this Question was Asked From

Continue Researching