How to Order 5 Foot Long RhinoFLEX Sewer Pipe with 90 Degree Elbow

Question

Question:

is there a kit like this with a 90 degree end??

asked by: Bob

0

Expert Reply:

What you need is the part # CAM39765 that you referenced as well as the fitting part # CAM39852 and you'd have what you are looking for.

expert reply by: Jameson C

0

Answer 1

The RhinoFLEX RV Sewer Hose Extension with Swivel Lug and Bayonet Fittings #CAM39765 and similar items do have removable orange fittings but there are not replacement parts available. If you have the fittings then you just need the hose #CAM39671. If…

view full answer...

Answer 2

There is an extension piece that you can use with your RhinoFlex sewer hose #CAM39761. It is a 5 foot length, #CAM39765. You could add this to get to 15 feet. I am not sure how much more length you would need but if you need more you could add…

view full answer...

Answer 3

The parts included with the Camco RhinoFLEX RV Sewer Hose #CAM39761 will include two storage caps and a 4 in 1 adapter. Here is a breakdown of everything included: 1 15 foot long hose 1 bayonet fitting. 2 storage caps. 1 elbow fitting. 1 4-in-1 dump…

view full answer...

Answer 4

Yes! The RhinoFLEX RV Sewer Hose Extension #CAM39765 is compatible with the RhinoEXTREME RV Sewer Hoses such as #CAM39861. I have linked videos of both products for you.

view full answer...

Answer 5

Yes, the fittings on the #CAM39765 would allow you to connect a few inline if you wanted. Basically one side of the hose is a male fitting and the other a female so you could keep connecting them and they would seal.

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

How to Order 5 Foot Long RhinoFLEX Sewer Pipe with 90 Degree Elbow

Product Page this Question was Asked From

Continue Researching