A-Frame Trailer-Mount Tool Boxes

Question

Question:

Hello, I am looking for a tongue toolbox for my PJ trailer: 36-48inch wide x 12inch deep x 12-16inch tall.

asked by: Steve

0

Expert Reply:

We have several styles of trailer-mount tool box shown on the linked page. These include products from Dee Zee, MaxxTow and RC Manufacturing and consist of A-frame and underbody-mount types.

DeeZee's A-Frame Trailer Tongue Toolbox # DZ91717 has dimensions close to those you're looking for: 34" Long (back) x 20" long (front) x 19" wide x 22" tall.

expert reply by: Adam R

0

Answer 1

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 2

Hubs will heat up when driving, but if it feels like they are getting too hot, then you will want to look at a few things on your hub. My guess is that the spindle nut is too tight and the added stress on the bearings is overheating the bearings and…

view full answer...

Answer 3

So long as a hub uses the correct bearings that match the dimensions of the spindle that is on the axle there is no worry about using two different brands of products, such as a Dexter hub on a Lippert axle. That in itself is not a concern. When a…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

For your Big Tex 90PI trailer, I recommend checking out the: -RC Manufacturing T-Series Trailer Tongue Tool Box #350980. This toolbox has a cargo capacity of 2.6 cubic feet, measures 30" long x 14-1/2" tall x 14-1/2" wide, and is…

view full answer...

Answer 6

The Pollak Heavy Duty 7-Way part #PK11720 that you referenced is a heavy duty style 7-way. If you check out the attached diagram you'll see how it should be wired.

view full answer...

Answer 7

To install the TorkLift PowerArmor Locking Battery Box #TLA7700L you'll need to use the included self-tapping screws to mount the box to your trailer tongue. You can do this either directly to your frame, using the extension brackets if they are…

view full answer...

Answer 8

The DeeZee Specialty Series Trailer Tongue Toolbox #DZ91717P is made of tough polyethylene plastic that is naturally non-corrosive and sturdy but it is not expressly meant for a person to step or stand on it. A child or a person that weighs 110-lbs…

view full answer...

Answer 9

I am happy to help you find a trailer tongue tool box for your Sure Trac trailer Andy. When you say you have 44 inches from the widest point, I believe you are referring to 44 inches up from the widest point of the A-frame towards the tailgate. You…

view full answer...

Answer 10

While a lot of wheels have cross compatibility with 1/2"-20 or 9/16"-18 wheel bolts, the Karrier ST235/80R16 Radial Trailer Tire with 16" Aluminum Wheel #KE39JR states that it only works with the 1/2"-20 wheel studs. We do have…

view full answer...

Answer 11

There sure is! The RC Manufacturing T-Series Trailer Tongue Tool Box - A-Frame - Aluminum - 2.6 Cu Ft in Silver #350970 or Black #350980 will fit in perfectly in your Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers - 300 lbs…

view full answer...

A-Frame Trailer-Mount Tool Boxes

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching