Do the Karrier ST235/80R16 Radial Trailer Tire with 16" Aluminum Wheels Fit 9/16" Wheel Studs

Question

Question:

Will this wheel work for 9/16inch lugs as well?

asked by: Matt B

0

Expert Reply:

While a lot of wheels have cross compatibility with 1/2"-20 or 9/16"-18 wheel bolts, the Karrier ST235/80R16 Radial Trailer Tire with 16" Aluminum Wheel # KE39JR states that it only works with the 1/2"-20 wheel studs.

We do have the Westlake ST235/80R16 Radial Tire w/ 16" Liger Aluminum Wheel # LH76FR available, that is a similar style but works with both 1/2"-20 or 9/16"-18 wheel studs.

expert reply by: Scott S

0

Answer 1

According to my contact at Dexter Axle, their Trailer Hub and Drum Assembly #42866UC3-EZ fits a wheel with a 4-3/4-inch pilot hole and a 8-on-6-1/2 bolt pattern. Each hub carries a 3500-lb rating.

view full answer...

Answer 2

Easiest way would be to use a strap like a bungee part #EM06701to wrap around the handle and jack body to hold the handle to the jack.

view full answer...

Answer 3

For your 8-285 hub and drum similar to the Dexter Hub and Drum, Oil Bath #8-285-9UC3 for 8K pound axles, the Dexter Electric Brake Assembly, Right Hand #23-435 and Left Hand #23-434 are the correct fit brake assemblies for your axle. Another great…

view full answer...

Answer 4

With the Timbren Axle-Less Trailer Suspension #TASR7KS02 rated for a 7,000lb capacity you will want to use either 2 of the Idler Hubs #AKIHUB-865-7-2-EZ-K or Hub/Drums #AKHD-865-7-1-EZ-K. We do have the Brake Kit #AKEBRK-7-SA if you go with the drum…

view full answer...

Answer 5

Do you by any chance mean 235/80-16 and 235/85-16? Because there isn't a 275 trailer tire size that I have seen. If so then the widths are the same between the two 235 sizes. The difference is overall diameter. The 235/80-16 is 30.9 inches in…

view full answer...

Answer 6

The Correct Track Tandem Lift Kit part #RR23QX that you referenced is exactly what you are looking for. This fits all RVs with tandem axle setups like your 2021 Grand Design Reflection 150 Series 268BH regardless of if the axles are above or below…

view full answer...

Answer 7

We don't have trailer specific fits on these but it looks like the GVWR of the Montana 3710FL is going to be around 16500-llbs; 4 of the Provider #A16RG8BML80 with a capacity of 4,450-lbs each will give you 17,800-lbs total capacity. You will…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

We don't have that exact part number but for basically the exact same hub except made by Dexter you'd want the part #8-219-13UC3. This is the sam 6k-7.2k hub with an 8 on 6-1/2 inch bolt pattern that uses 9/16 inch studs just like the one you…

view full answer...

Answer 10

95 ft lbs would be good for torquing the lug nuts of the trailer hub part #8-219-4UC3-EZ to a 17.5 inch diameter trailer wheel. The acceptable range would be 90 to 120 ft lbs for your setup.

view full answer...

Answer 11

The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn. If the spindle uses a castle nut and cotter pin or tang nut, tighten the nut finger tight until it…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Do the Karrier ST235/80R16 Radial Trailer Tire with 16" Aluminum Wheels Fit 9/16" Wheel Studs

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching