Recommended Keyed Alike Cam Door Locks 1-3/8 Inches Long

Question

Question:

mine measures 13/8 inches . I want it keyed the same as the other locks. key no. ch751

asked by: JOE S

0

Expert Reply:

We have the Replacement Cam Lock Cylinder for RVs - Keyed Alike Option - Stainless Steel - 1-3/8" Long # 295-000005 which can be keyed alike in whatever quantity you need, but I don't have the lock cylinder to match the key number you gave to replace a single lock.

expert reply by: Jason S

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 5

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 6

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 7

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Answer 8

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 9

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 10

If you have the Gooseneck versions of the Curt CrossWing ( #C92DR or #C32DR) you unfortunately would not be able to use the Rota-Flex with it. The pivoting head causing too much strain for the single point of contact you have with a gooseneck hitch.…

view full answer...

Answer 11

The cone that you see in the picture you attached of the Curt Crosswing part #C86JR is there to help align it with the rest of the hitch when you back the vehicle up into it and lower it down with the jacks. This ensures it is completely seated and…

view full answer...

Answer 12

The Curt CrossWing Lightweight 5th Wheel Trailer Hitch item #C86JR weighs only 60 lbs. This is the one that mounts to industry standard 5th wheel rails. I have linked a review video below so you can see the functions of this hitch demonstrated.

view full answer...

Recommended Keyed Alike Cam Door Locks 1-3/8 Inches Long

Product Page this Question was Asked From

Continue Researching