Only Brake Lights are Working on Trailer with All New Lights
Question:
My lights on my trailer are all new. They only work when the brakes are pressed. Also if the headlights are on they wont work at all. Please help.
asked by: Aaron
Expert Reply:
It sounds like a short, ground problem, or wiring issue. There are some things you can check to determine where the issue is.
First, disconnect the trailer from the tow vehicle. Then make sure that the vehicle side trailer connector is clean and free of corrosion inside, where the wires attach (if possible) and outside on the pins. Corrosion can interrupt the transfer of electricity from the tow vehicle to the trailer.
Next, use a circuit tester such as # PTW2993 or a meter if you have one to test the pins on the vehicle side connector. Have someone sit in the vehicle and operate the light functions while you test. If none of the pins have power when the turn signals are activated or when the running lights are on, then there is a problem on the vehicle side; potentially a miswired connector or blown or missing fuses or relays (on vehicles with a factory tow package).
If everything is working as it should on the vehicle side, then the issue must be on the trailer. Check the trailer connector for corrosion too. You can trace the wiring from front to back and fix and damaged or pinched wires.
If it is a ground issue, then ground problems normally show up when there is more draw on a system such as when you have the running lights on and then use another function like a turn signal or brake light but can show up any time.
The light grounds should also be attached to clean and corrosion free bare metal surfaces. If there is anything between a light ground and the metal trailer frame or if the trailer has an aluminum frame, tilt bed, or folding tongue, any of these things can interrupt the ground. Running jumper wires from the light grounds to the main trailer connector ground can help.
I have included links to a couple of help articles that may also help.
Product Page this Question was Asked From
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Wiring New 4-Way Connector on Trailer with 5 Wires
- Article: Trailer Wiring Diagrams
- Q&A: How to Get Separate Turn Signals and Brake Lights to Work on a Trailer
- Q&A: Working Running Lights, But No Turn Signals or Brake Lights On Trailer
- Q&A: When Using Bearing Buddy Bearing Protectors Do I Need To Repack Bearings Periodically?
- Shop: Hopkins Plug-In Simple Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: EZ Connector Magnetic 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Way Connector - Watertight Seal
- Shop: Hook Probe Circuit Tester
- Shop: Right Angle 2-Wire Pigtail for Optronics Trailer Lights - 2-Prong PL-10 Plug - 6" Lead
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 4-Way and 7-Pole Connector - 7' Long
- Video: Optronics Trailer Clearance Side Marker Lights Single Wire Plug Review
- Q&A: Signal and Brake Lights Work on Trailer but No Taillights
- Q&A: Why Does 4-Pin Trailer Wiring Have 5 Wires
- Q&A: Trailer Running Lamp Fuse Location on 2003 Chevy Suburban
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Shop: Brake Controller
- Shop: Truck Bed Tailgate Assist
- Shop: Gooseneck Hitch
- Shop: Tailgate
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Search Results: brake controller
- Video: Choosing the Right Brake Controller
- Search Results: hitch
on Wiring
