Are End Links Needed for Anti-Sway Bar on 1999 Ford F-350 With a 4-Inch Lift?

Question

Question:

I have 1999 f350. Super duty. 4x4 , W/ 4in lift Please advice, end links and do I need to remove my spare tire? Thank you

asked by: Simon P

0

Expert Reply:

Since your 1999 Ford F-350 has a 4" lift, the Roadmaster Rear Anti-Sway Bar for Pickup Trucks # RM-1139-153 is going to require you to use the End Link Kit for Roadmaster Rear Anti-Sway Bar # RM-590039-00. The spare tire will not need to be removed when using this Anti-Sway bar.

expert reply by: Kyle S

0

Answer 1

I spoke with my contact at Roadmaster and the length of the rods on end link kit #RM-590039-00 are 18 inches from eye center to eye center.

view full answer...

Answer 2

Since your 2001 Ford F-350 has a 4 inch lift you'd just need the end link kit part #RM-590039-00 with the rear sway bar part #RM-1139-153 and you'd be set.

view full answer...

Answer 3

We have the Roadmaster sway bar part #RM-1139-153 which is a confirmed fit for your 2003 Ford F-350 4x4 with single rear wheel axle. This is a thicker 1-1/4 inch bar that replaces the sway bar you currently have. No other parts needed to install it.…

view full answer...

Answer 4

I have the perfect options for you. In order to level the rear of your 2000 Ford F-250, I recommend using a set of heavy duty jounce springs such as the Timbren Rear Suspension Enhancement System part #TFRTT350E or a set of rear air bags like the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...